Classification 1
Example values from the apprentices page: a 1 to 1 ratio, two journeyworker electricians and three apprentices for 8 hours, $35.00 plus $15.00 fringe, apprentices at 60 percent. Replace them with your own.
How the checker works
29 CFR 5.5(a)(4)(i)(C)29 CFR 5.5Code of Federal Regulations, eCFR sets the cap: “The allowable ratio of apprentices to journeyworkers on the job site in any craft classification must not be greater than the ratio permitted to the contractor as to the entire work force under the registered program or the ratio applicable to the locality of the project” (29 CFR 5.5(a)(4)(i)). The checker multiplies the journeyworkers on site by the ratio you type to get the apprentices allowed, then compares the apprentices on site. Enter one day at a time: “Compliance with the applicable ratio is determined on a daily, not weekly basis.”
- Count journeyworkers in the same craft who supervise for the full day. The Resource Book says a journeyworker who splits a day between two apprentices supervises each for only half a day, which does not count unless the program allows partial supervision.
- Round down. A part crew does not earn an extra apprentice: the Resource Book says a “fraction thereof” “in computing apprenticeship ratios is not permitted unless specified in the approved apprenticeship program”. Tick the box only if your program says so.
- Use the right ratio. Working outside your program’s area, “the ratios and wage rates (expressed in percentages of the journeyworker's hourly rate) applicable within the locality in which the construction is being performed must be observed” (29 CFR 5.5(a)(4)(i)(D))29 CFR 5.5Code of Federal Regulations, eCFR.
Over the ratio: the journeyworker rate
The rule is direct: “any apprentice performing work on the job site in excess of the ratio permitted under this section must be paid not less than the applicable wage rate on the wage determination for the work actually performed”. The Resource Book says which ones: “only the individuals who were working before the applicable ratio was exceeded may be paid less than the wage determination rate(s) for the work performed”. So the apprentices who arrived after the ratio was reached are the ones owed the full rate that day.
The dollar difference
Within the ratio, each apprentice is paid the program’s percentage, “calculated as a percent of the basic hourly rate required by the applicable wage determination for the applicable classification”. Fringe follows the program, and “If the apprenticeship program does not specify fringe benefits, apprentices must be paid the full amount of fringe benefits listed on the wage determination for the applicable classification.” Over the ratio, the program’s fringe terms fall away too: Fact Sheet 66E says “those provisions only apply when the apprentices are employed in accordance with the applicable ratio of journeyworkers to apprentices and other specifications of the program” (Fact Sheet 66E).
So the checker compares the full journeyworker rate (basic plus fringe) with what the apprentice would have been paid (the program’s percentage of the basic rate plus the apprentice fringe). In the example values, the electrician rate is $35.00 plus $15.00 = $50.00. A 60 percent apprentice with no program fringe terms gets $21.00 plus $15.00 = $36.00. The third apprentice on a 1 to 1 ratio with two journeyworkers is owed $14.00 more an hour: $112.00 for an 8-hour day.
Who counts as an apprentice
Only a worker individually registered in a program registered with DOL’s Office of Apprenticeship or a recognized State Apprenticeship Agency, or a certified probationer in the first 90 days, can be paid less. Anyone else is outside the ratio math entirely: “Any worker listed on a payroll at an apprentice wage rate, who is not registered or otherwise employed as stated in paragraph (a)(4)(i)(A) of this section, must be paid not less than the applicable wage rate on the wage determination for the classification of work actually performed.” Leave them out of the apprentice count.
Records
Keep proof of the ratio you rely on. Contractors with apprentices must keep “written evidence of the registration of apprenticeship programs, the registration of the apprentices, and the ratios and wage rates prescribed in the applicable programs” (29 CFR 5.5(a)(3)(i)(D))29 CFR 5.5Code of Federal Regulations, eCFR. On the WH-347, column 2 shows “RA” and the level of progression for each registered apprentice. Ratio errors are among the common certified payroll errors, and the back wages can be withheld from contract payments; see withholding and debarment. The full rules are on the apprentices page. The IRS apprenticeship ratio for the clean energy credits is a separate test.
The checker uses the ratio you type. It cannot read your program standards or tell which ratio applies in the project’s locality. General information, not legal advice.
Questions filers ask
Is the apprentice ratio checked weekly or daily?
Daily. If the ratio is exceeded on any day, the apprentices over the ratio that day are owed the full wage determination rate for their hours that day.
Which apprentices get the journeyworker rate when we go over?
The ones who started work after the ratio was reached. The Resource Book says only the individuals working before the ratio was exceeded may be paid less.
Does an over-ratio apprentice also get the full fringe?
Yes. The program’s fringe terms apply only within the ratio, so the full fringe on the wage determination is owed along with the full basic rate.
Our program uses a sliding ratio. How do I enter it?
Work out how many apprentices the program allows for that day’s crew and type the number in the optional allowed field. It overrides the simple ratio.